Interval Extension Coverage Gap (IECG)

GMI-RE-045Renewable EnergyIntegration-RequiredPattern O-7: Inspection Coverage

Definition

Proportion of failure modes originally covered by a time-based PM that the condition-based system extending that PM interval does not monitor. Extending a PM from six months to twelve on healthy vibration readings doubles exposure time for every failure mode vibration cannot see.

The Measurement Gap

The Measurement Gap

Condition-based maintenance systems justify interval extensions by demonstrating that monitored parameters indicate healthy asset condition. If vibration levels are within normal range, oil analysis shows clean fluid, and temperature trends are stable, the CBM model recommends extending the next scheduled PM. This logic is sound for the failure modes that the sensors monitor. The gap is that time-based PMs typically cover multiple failure modes, and the CBM sensors only monitor a subset of them.

A gearbox PM might cover bearing condition (monitored by vibration sensors), oil quality (monitored by oil analysis), seal integrity (partially monitored by oil contamination trends), gear tooth wear (partially monitored by vibration harmonics), housing crack propagation (not monitored), fastener torque relaxation (not monitored), and cooling system blockage (not monitored). When the CBM model extends this PM from 6 to 12 months because vibration and oil analysis look healthy, the unmonitored failure modes (housing cracks, fastener relaxation, cooling blockage) lose their inspection opportunity for an additional 6 months. If any of those modes progress to failure during the extended interval, the CBM system provided false assurance by extending coverage for modes it could see while removing coverage for modes it could not.

The Decision It Enables

IECG quantifies the coverage gap so that interval extension decisions include explicit risk acknowledgment for unmonitored failure modes. When IECG is low (below 15%), the CBM system covers most of what the PM was designed to address, and the interval extension is well-supported. When IECG is high (above 30%), the interval extension creates significant exposure for unmonitored modes, and supplemental inspections should be scheduled at the original interval for those specific failure modes. This transforms interval extension from a binary decision (extend or do not extend) into a layered decision where the full PM interval can be extended for monitored modes while targeted inspections continue at the original interval for unmonitored modes.

Formula

Primary Formula:

IECG = (FM_Total_PM minus FM_Monitored_CBM) / FM_Total_PM x 100

Variable Definitions:

Variable Definition
FM_Total_PM the total number of distinct failure modes addressed by the original time-based PM task, as documented in the PM procedure and supporting reliability analysis (FMEA or equivalent)
FM_Monitored_CBM the number of failure modes from that original PM scope that are actively monitored by the condition-based monitoring system that justified the interval extension

Calculation Example:

A wind turbine main bearing PM is designed to address 8 failure modes: inner race spalling, outer race spalling, cage wear, seal degradation, lubricant contamination, lubricant viscosity breakdown, housing crack propagation, and bolt torque relaxation. The CBM system monitors 5 of these through vibration analysis (inner/outer race spalling, cage wear) and oil analysis (lubricant contamination, viscosity breakdown). Three failure modes (seal degradation, housing crack propagation, bolt torque relaxation) are not monitored. IECG = (8 minus 5) / 8 x 100 = 37.5%. More than a third of the failure modes covered by the original PM will lose their inspection coverage during the extended interval.

Scoring Refinement:

Failure modes that are partially monitored (the sensor detects some manifestations but not all) should be classified as "partially monitored" and weighted at 0.5 rather than 1.0 for the FM_Monitored_CBM count. PMs with vague scope descriptions such as "general inspection" should be decomposed into specific failure modes before computing IECG. New failure modes discovered after the PM was originally designed should be included in FM_Total_PM if the PM procedure would have detected them during execution.

Edge Cases and Measurement Boundaries:

The accuracy of IECG depends entirely on the quality of the failure mode enumeration for each PM. If the PM procedure does not explicitly list the failure modes it covers, the enumeration must be reconstructed from the procedure steps, which requires reliability engineering judgment. PMs that have been extended without a formal IECG analysis may have been running with significant unmonitored gaps for years. Computing IECG retroactively for these PMs often reveals gaps that have been tolerated unknowingly.

Proposed formula, pending validation pilots.

At a Glance

Unit
Percentage
Trend Direction
Lower; smaller coverage gap
Reporting Frequency
Per extended-interval PM
Category
Condition-Based Maintenance Integrity
← CBM Sensor Health Correlation Index (CSHCI)OEM Bulletin Response Accuracy (OBRA) →

Assess Your Organization

The AI-GPS Assessment evaluates your AI governance maturity and recommends KPIs like this one for your implementation roadmap.

Take the Free AI-GPS Assessment